Namaste ! Vanakkam ! Namashkara ! Jai Jinendra ! India

Free Shipping for Normal Deliveries on orders above Rs. 999
Official Store • 2 Year Direct Warranty • GST invoice
1 9
Ugreen  |  SKU: 50248
37% off
New arrival

UGREEN 50248 Cat6 Shielded RJ45 Modular Plugs, 100-Pack

Rs. 1,055.00 Rs. 1,665.00
Tax included Shipping calculated at checkout.

Secure Signal
Fast Data
Easy Install
Interference Shielded
Reliable Link
CAT6 SHIELDED • 8P8C • 100 PACK

UGREEN 50248 Cat6 Shielded RJ45 Modular Plugs, 100-Pack

Overview

UGREEN 50248 is a bulk pack of 100 shielded Cat6 8P8C modular plugs for making or repairing compatible terminated Ethernet leads. Each plug provides a male RJ45-style cable end. Its metal shell is intended to continue shielding when used with suitable shielded cable, termination practice and grounded equipment design. This guide explains selection, installation, compatibility, real limitations and safe use without treating a passive accessory as active networking equipment.

Exact SKU 50248ACTIVE productCAT6 SHIELDED • 8P8C • 100 PACK
UGREEN 50248 exact product overview
UGREEN 50248 exact product overview
1

Key features

Exact role

Each plug provides a male RJ45-style cable end. Its metal shell is intended to continue shielding when used with suitable shielded cable, termination practice and grounded equipment design.

Compatibility boundary

Compatible Cat6 shielded cable whose conductor construction and listed 0.96–1.02mm diameter fit the plug. Exact UGREEN text mentions both single- and multi-strand conductors, but a trial termination is strongly advised before a bulk project.

Performance reality

A connector alone cannot guarantee Cat6 or Gigabit performance. Cable geometry, pair untwist, conductor fit, crimp quality, patch length and all network equipment determine the finished channel.

Important exclusion

This is not for oversized Cat6A/Cat7/Cat8 cable by assumption, not a pass-through plug, not a female coupler, not a cable tester and not a substitute for shield continuity and link testing.

2

Where it fits in the connection

1. Network device
2. Crimped plug
3. Matched cable
4. Crimped plug
5. Network device

The system rule: every stage must match. The lowest-rated, damaged or incorrectly terminated component can limit speed, reliability, shielding, PoE operation or serviceability.

3

Use scenarios

Scenario 1

Custom shielded Cat6 patch leads where every component is matched.

Scenario 2

Repairing a damaged connector after confirming cable geometry and conductor fit.

Scenario 3

Bulk office, rack or installation work with sample-first quality control.

Scenario 4

Maintaining shield continuity in a properly designed shielded cabling system.

4

Compatibility and selection guide

Use when

Compatible Cat6 shielded cable whose conductor construction and listed 0.96–1.02mm diameter fit the plug. Exact UGREEN text mentions both single- and multi-strand conductors, but a trial termination is strongly advised before a bulk project.

Do not assume

not for oversized Cat6A/Cat7/Cat8 cable by assumption, not a pass-through plug, not a female coupler, not a cable tester and not a substitute for shield continuity and link testing.

Before bulk purchase: trial the exact cable, module, plug or rack fit and complete one tested installation. Small physical differences can matter even within the same category name.

UGREEN 50248 construction or installation detail
UGREEN 50248 construction or installation detail
5

Setup and usability guidance

  1. Step 1: Confirm the cable category, shielding, conductor construction and listed conductor diameter fit before cutting.
  2. Step 2: Slide on any separately selected boot before preparing the cable.
  3. Step 3: Strip only enough jacket for termination and keep pair untwist to a minimum.
  4. Step 4: Arrange conductors to the selected T568A or T568B scheme and trim them evenly.
  5. Step 5: Insert every conductor fully, check colour order and ensure the cable jacket/strain relief is correctly captured.
  6. Step 6: Crimp with a compatible die, inspect all eight contacts and shield engagement, then test wire map and real network negotiation.

Work cleanly: dust, copper scraps and loose braid strands can create faults. Collect offcuts and inspect the finished area before energising connected equipment.

6

Compatible devices and systems

Network endpoints

Routers, switches, access points, computers, printers, smart televisions, cameras and other RJ45 network equipment only through a correctly built compatible link.

Structured cabling

Wall outlets, patch panels, permanent cable and patch leads must share a suitable category, shielding design and wiring scheme.

PoE equipment

Possible only within the verified boundary: PoE is not independently guaranteed by the plug listing. Use only in a complete compliant channel with suitable conductor material, gauge, connector fit, heat management and powered equipment.

Operating systems

No operating-system driver is required for this passive accessory or manual tool; active adapters and switches are separate products.

7

What this product does

  • Provides its exact documented function: Each plug provides a male RJ45-style cable end. Its metal shell is intended to continue shielding when used with suitable shielded cable, termination practice and grounded equipment design.
  • Supports the stated compatibility class: Compatible Cat6 shielded cable whose conductor construction and listed 0.96–1.02mm diameter fit the plug. Exact UGREEN text mentions both single- and multi-strand conductors, but a trial termination is strongly advised before a bulk project.
  • Can form part of a serviceable labelled network: when installed with matched components and tested.
  • Keeps infrastructure modular: damaged or changed portions can be traced and replaced without rebuilding unrelated equipment.
  • Uses no software: this product is passive or manual and has no configuration app.
8

What this product does not do

  • It is not for oversized Cat6A/Cat7/Cat8 cable by assumption, not a pass-through plug, not a female coupler, not a cable tester and not a substitute for shield continuity and link testing.
  • It does not upgrade a lower-category cable or repair split pairs, poor conductor material, corrosion or bad device ports.
  • It does not guarantee PoE, bandwidth or error-free operation without a compliant complete link.
  • It does not remove the need for correct tools, installation practice, labelling and testing.
  • It should not be installed outdoors, in wet areas or beside mains wiring without a suitable compliant enclosure and qualified design.
9

What to do

Match

Match the exact SKU: use the title, construction and limits for 50248 rather than borrowing specifications from a similar family member.

Check

Check the complete path: confirm cable category, shielding, conductor construction, connector geometry, patch leads and endpoints.

Label

Label both ends: record room/port, wiring scheme and destination so later maintenance does not become guesswork.

Test

Test in stages: verify the cable or module before closing a wall plate or rack, then test again after final assembly.

Protect

Protect bend radius and strain relief: route cable gently and keep load away from contacts, IDC slots and device sockets.

10

What not to do

Do not force

Do not force parts: a keystone, plug, cable or tool that does not fit cleanly is probably the wrong geometry.

Do not miswire

Do not mix T568A and T568B accidentally: document the chosen scheme and check all eight conductors.

Do not over-untwist

Do not untwist pairs excessively: preserving pair geometry near termination matters to high-frequency performance.

Do not guess

Do not claim speed from appearance: clear housings, gold colour or a category marking do not replace complete-link testing.

Do not reuse damage

Do not use damaged parts: discard cracked housings, bent contacts, dull blades, loose shutters or failed crimp terminations.

11

Warnings and limitations

  • Sharp tools and contacts: keep fingers clear of blades, IDC contacts, trimmed conductors and crimp dies. Wear appropriate eye protection during cutting and termination.
  • Indoor low-voltage scope: no outdoor ingress rating is established. Keep the product dry, clean and away from corrosive environments or excessive heat.
  • Category is system-wide: a Cat5e, Cat6 or Cat7 label on one part does not upgrade the remaining cable, patch leads, terminations or equipment.
  • Test before service: visual inspection is not enough. Verify conductor map and real link negotiation; professional installations may require certification testing.
  • Do not work on live mains: networking hardware is low voltage, but wall boxes and racks may be close to hazardous electrical circuits.

Exact model limit: A connector alone cannot guarantee Cat6 or Gigabit performance. Cable geometry, pair untwist, conductor fit, crimp quality, patch length and all network equipment determine the finished channel.

12

Technical specifications

Brand / SKU UGREEN 50248
Product role a bulk pack of 100 shielded Cat6 8P8C modular plugs for making or repairing compatible terminated Ethernet leads
Product type Shielded modular plugs for cable termination
Category Cat6
Connector 8P8C male modular plug
Pack quantity 100
Shielding Metal shielded casing
Contacts 3U gold-plated, as listed
Listed conductor diameter 0.96–1.02mm
Cable construction note Exact page mentions single- and multi-strand conductors; verify actual fit
Termination Crimp; compatible tool required
Electronics None; passive
Verified source https://www.ugreenindia.com/products/ugreen-cat-6-shielded-crystal-head-100-pcs50248
13

Product research and claim reconciliation

Primary source: exact UGREEN India SKU page and the current live Shopify product record.

Visual check: Exact media confirms the shielded metal shell, 8P8C structure, 3U contact artwork and T568A/B wiring reference. The page later drifts into language about a complete “cable” and outdoor use; those claims were rejected because SKU 50248 is a connector pack only. No Cat6A/Cat7/Cat8 fit is inferred.

Claim policy: conflicting family artwork, mistranslated metadata, impossible dimensions and adjacent-model specifications are excluded rather than averaged together.

UGREEN 50248 exact detail retained after conflict review
UGREEN 50248 exact detail retained after conflict review
14

Troubleshooting checklist

No link

Confirm both active devices, patch leads and port selections. Then check conductor map, full insertion and the exact connector/cable fit.

Lower speed than expected

Verify negotiation settings and every component category. Excessive untwist, split pairs and unsuitable cable construction can pass continuity yet fail performance.

Intermittent link

Look for incomplete seating, weak strain relief, damaged latch, nicked conductor, IDC not fully closed or a crimp made with the wrong die.

PoE device restarts

Stop use and inspect conductor material, gauge, contact engagement, heat and the powered equipment budget. Do not continue with a hot or damaged termination.

Shield or noise concern

For shielded products, check end-to-end shield design and grounding practice. Mixing shielded and unshielded parts can defeat the intended system.

Port or label mismatch

Trace one cable at a time, compare labels at both ends and update records immediately after correction.

15

Package contents

In the box

100 × UGREEN 50248 Cat6 shielded 8P8C modular plugs. Ethernet cable, strain-relief boots, crimping tool and tester are not identified as included.

Devices, cables, racks, wall boxes, modules, tools and testers are not included unless explicitly named above.

16

Product-specific FAQ

What exactly is UGREEN 50248?
A bulk pack of 100 shielded Cat6 8P8C modular plugs for making or repairing compatible terminated Ethernet leads.
What is included in the package?
100 × UGREEN 50248 Cat6 shielded 8P8C modular plugs. Ethernet cable, strain-relief boots, crimping tool and tester are not identified as included.
Which cables, modules or devices are compatible?
Compatible Cat6 shielded cable whose conductor construction and listed 0.96–1.02mm diameter fit the plug. Exact UGREEN text mentions both single- and multi-strand conductors, but a trial termination is strongly advised before a bulk project.
Does it guarantee the advertised network speed?
A connector alone cannot guarantee Cat6 or Gigabit performance. Cable geometry, pair untwist, conductor fit, crimp quality, patch length and all network equipment determine the finished channel. Test the complete channel rather than judging one component in isolation.
Can it be used in a PoE network?
PoE is not independently guaranteed by the plug listing. Use only in a complete compliant channel with suitable conductor material, gauge, connector fit, heat management and powered equipment.
Which tools are required?
A compatible standard modular-plug crimping tool, cable preparation tools and a cable tester are required. Verify the crimp die and strain-relief method on a sample before production work.
Does it split, switch, route or convert a network connection?
No. not for oversized Cat6A/Cat7/Cat8 cable by assumption, not a pass-through plug, not a female coupler, not a cable tester and not a substitute for shield continuity and link testing. Any active switching, routing, conversion or power function requires separate purpose-built equipment.
How should a finished installation be tested?
Start with a wire-map or continuity test that checks all required conductors and shield where applicable. Then connect known-good equipment, confirm negotiated link speed and observe errors under normal traffic.
Is it suitable for outdoor or mains-power installation?
No outdoor or ingress-protection rating is verified. This is a low-voltage networking accessory; it is not a mains device. Follow separation, fire, grounding and building rules.
What should I do if the link is intermittent?
Remove power where applicable, inspect for partial insertion, wrong colour order, excessive untwist, nicked conductors, poor strain relief or an incompatible cable/connector fit. Reterminate only with matched parts, then test again.
How is this exact SKU different from similar UGREEN products?
Exact media confirms the shielded metal shell, 8P8C structure, 3U contact artwork and T568A/B wiring reference. The page later drifts into language about a complete “cable” and outdoor use; those claims were rejected because SKU 50248 is a connector pack only. No Cat6A/Cat7/Cat8 fit is inferred.

Exact-model check before ordering

Match SKU 50248, product type, port or die count, cable category/construction and package contents. Similar UGREEN networking accessories can look nearly identical while using different shielding, conductor fit, rack format or termination method.

SKU 50248CAT6 SHIELDED • 8P8C • 100 PACK

GST Invoice available, just mail back with details to order confirmation mail.

Buy direct from official UGREEN India

GST Invoice, Warranty, authenticity, faster support
Back to top