Namaste ! Vanakkam ! Namashkara ! Jai Jinendra ! India

Free Shipping for Normal Deliveries on orders above Rs. 999
Official Store • 2 Year Direct Warranty • GST invoice
1 5
Ugreen  |  SKU: 70423
40% off
New arrival

UGREEN 70423 24-Port Cat6 UTP Patch Panel, 1U 19-Inch

Rs. 3,333.00 Rs. 5,553.00
Tax included Shipping calculated at checkout.

Secure Connections
Fast Setup
Neat Cables
Robust Build
Easy Labeling
24 PORTS • CAT6 UTP • 1U 19-INCH

UGREEN 70423 24-Port Cat6 UTP Patch Panel, 1U 19-Inch

Overview

UGREEN 70423 is a passive 24-port Cat6 UTP patch panel for terminating and organising permanent network runs in a standard 19-inch rack position. Each front RJ45 socket maps to a rear colour-coded IDC termination. The panel creates a managed cross-connect point between permanent cabling and short patch leads to a switch or other network equipment. This guide explains selection, installation, compatibility, real limitations and safe use without treating a passive accessory as active networking equipment.

Exact SKU 70423ACTIVE product24 PORTS • CAT6 UTP • 1U 19-INCH
UGREEN 70423 exact product overview
UGREEN 70423 exact product overview
1

Key features

Exact role

Each front RJ45 socket maps to a rear colour-coded IDC termination. The panel creates a managed cross-connect point between permanent cabling and short patch leads to a switch or other network equipment.

Compatibility boundary

A standard 19-inch rack/cabinet with 1U space, compatible Cat6 UTP permanent cable, suitable patch leads and T568A/B installation practice. Rack nuts and mounting method must match the actual rack rails.

Performance reality

Cat6 performance depends on correct pair placement, minimal untwist, cable construction, patch leads, installation quality and test results. The panel is passive and has no switching bandwidth of its own.

Important exclusion

This is not an Ethernet switch, router, PoE injector, unmanaged hub, shielded grounding panel, wall faceplate or substitute for rack cable management and channel certification.

2

Where it fits in the connection

1. Switch patch lead
2. Front RJ45 port
3. Rear IDC
4. Permanent cable
5. Room outlet

The system rule: every stage must match. The lowest-rated, damaged or incorrectly terminated component can limit speed, reliability, shielding, PoE operation or serviceability.

3

Use scenarios

Scenario 1

A 24-run office or classroom structured-cabling cabinet.

Scenario 2

A home lab or equipment rack needing labelled permanent links.

Scenario 3

Separating fixed building cable from replaceable switch patch leads.

Scenario 4

Making adds, moves and fault isolation easier through numbered ports.

4

Compatibility and selection guide

Use when

A standard 19-inch rack/cabinet with 1U space, compatible Cat6 UTP permanent cable, suitable patch leads and T568A/B installation practice. Rack nuts and mounting method must match the actual rack rails.

Do not assume

not an Ethernet switch, router, PoE injector, unmanaged hub, shielded grounding panel, wall faceplate or substitute for rack cable management and channel certification.

Before bulk purchase: trial the exact cable, module, plug or rack fit and complete one tested installation. Small physical differences can matter even within the same category name.

UGREEN 70423 construction or installation detail
UGREEN 70423 construction or installation detail
5

Setup and usability guidance

  1. Step 1: Reserve one 1U position in a compatible 19-inch rack and plan cable approach, bend radius and strain relief.
  2. Step 2: Label every permanent cable at both ends before termination.
  3. Step 3: Route cables through the rear support, leave service slack and avoid tight ties or sharp bends.
  4. Step 4: Choose T568A or T568B consistently and place conductors in the matching colour-coded IDC positions.
  5. Step 5: Terminate with a suitable tool while keeping pair untwist minimal; trim safely and secure cables at the rear.
  6. Step 6: Fit replaceable labels, mount the panel, test every port to the required standard and patch it to active equipment.

Work cleanly: dust, copper scraps and loose braid strands can create faults. Collect offcuts and inspect the finished area before energising connected equipment.

6

Compatible devices and systems

Network endpoints

Routers, switches, access points, computers, printers, smart televisions, cameras and other RJ45 network equipment only through a correctly built compatible link.

Structured cabling

Wall outlets, patch panels, permanent cable and patch leads must share a suitable category, shielding design and wiring scheme.

PoE equipment

Possible only within the verified boundary: The panel is passive. No explicit PoE class/current ceiling is verified for SKU 70423; PoE use requires a complete compliant copper channel, correct IDC terminations and thermal/bundle assessment.

Operating systems

No operating-system driver is required for this passive accessory or manual tool; active adapters and switches are separate products.

7

What this product does

  • Provides its exact documented function: Each front RJ45 socket maps to a rear colour-coded IDC termination. The panel creates a managed cross-connect point between permanent cabling and short patch leads to a switch or other network equipment.
  • Supports the stated compatibility class: A standard 19-inch rack/cabinet with 1U space, compatible Cat6 UTP permanent cable, suitable patch leads and T568A/B installation practice. Rack nuts and mounting method must match the actual rack rails.
  • Can form part of a serviceable labelled network: when installed with matched components and tested.
  • Keeps infrastructure modular: damaged or changed portions can be traced and replaced without rebuilding unrelated equipment.
  • Uses no software: this product is passive or manual and has no configuration app.
8

What this product does not do

  • It is not an Ethernet switch, router, PoE injector, unmanaged hub, shielded grounding panel, wall faceplate or substitute for rack cable management and channel certification.
  • It does not upgrade a lower-category cable or repair split pairs, poor conductor material, corrosion or bad device ports.
  • It does not guarantee PoE, bandwidth or error-free operation without a compliant complete link.
  • It does not remove the need for correct tools, installation practice, labelling and testing.
  • It should not be installed outdoors, in wet areas or beside mains wiring without a suitable compliant enclosure and qualified design.
9

What to do

Match

Match the exact SKU: use the title, construction and limits for 70423 rather than borrowing specifications from a similar family member.

Check

Check the complete path: confirm cable category, shielding, conductor construction, connector geometry, patch leads and endpoints.

Label

Label both ends: record room/port, wiring scheme and destination so later maintenance does not become guesswork.

Test

Test in stages: verify the cable or module before closing a wall plate or rack, then test again after final assembly.

Protect

Protect bend radius and strain relief: route cable gently and keep load away from contacts, IDC slots and device sockets.

10

What not to do

Do not force

Do not force parts: a keystone, plug, cable or tool that does not fit cleanly is probably the wrong geometry.

Do not miswire

Do not mix T568A and T568B accidentally: document the chosen scheme and check all eight conductors.

Do not over-untwist

Do not untwist pairs excessively: preserving pair geometry near termination matters to high-frequency performance.

Do not guess

Do not claim speed from appearance: clear housings, gold colour or a category marking do not replace complete-link testing.

Do not reuse damage

Do not use damaged parts: discard cracked housings, bent contacts, dull blades, loose shutters or failed crimp terminations.

11

Warnings and limitations

  • Sharp tools and contacts: keep fingers clear of blades, IDC contacts, trimmed conductors and crimp dies. Wear appropriate eye protection during cutting and termination.
  • Indoor low-voltage scope: no outdoor ingress rating is established. Keep the product dry, clean and away from corrosive environments or excessive heat.
  • Category is system-wide: a Cat5e, Cat6 or Cat7 label on one part does not upgrade the remaining cable, patch leads, terminations or equipment.
  • Test before service: visual inspection is not enough. Verify conductor map and real link negotiation; professional installations may require certification testing.
  • Do not work on live mains: networking hardware is low voltage, but wall boxes and racks may be close to hazardous electrical circuits.

Exact model limit: Cat6 performance depends on correct pair placement, minimal untwist, cable construction, patch leads, installation quality and test results. The panel is passive and has no switching bandwidth of its own.

12

Technical specifications

Brand / SKU UGREEN 70423
Product role a passive 24-port Cat6 UTP patch panel for terminating and organising permanent network runs in a standard 19-inch rack position
Product type Passive rack-mount patch panel
Category Cat6 UTP
Front ports 24 × RJ45 female
Rear termination Colour-coded IDC
Wiring schemes T568A / T568B
Rack format 1U, standard 19-inch
Labelling Replaceable front label strip with numbered ports
Cable support Rear cable-management loops / bar
Contact treatment Nickel-chromium and gold-plated process, as listed
Active electronics None
Verified source https://www.ugreenindia.com/products/ugreen-cat-6-1u-24-port-utp-patch-panel-70423
13

Product research and claim reconciliation

Primary source: exact UGREEN India SKU page and the current live Shopify product record.

Visual check: Exact media confirms 24 front ports, rear T568A/B IDC blocks, 1U rack ears, removable label cover, cable ties and the compact yellow preparation tool. The rack width is stated as standard 19-inch; questionable package-size data and unverified third-party test wording are not presented as product specifications.

Claim policy: conflicting family artwork, mistranslated metadata, impossible dimensions and adjacent-model specifications are excluded rather than averaged together.

UGREEN 70423 exact detail retained after conflict review
UGREEN 70423 exact detail retained after conflict review
14

Troubleshooting checklist

No link

Confirm both active devices, patch leads and port selections. Then check conductor map, full insertion and the exact connector/cable fit.

Lower speed than expected

Verify negotiation settings and every component category. Excessive untwist, split pairs and unsuitable cable construction can pass continuity yet fail performance.

Intermittent link

Look for incomplete seating, weak strain relief, damaged latch, nicked conductor, IDC not fully closed or a crimp made with the wrong die.

PoE device restarts

Stop use and inspect conductor material, gauge, contact engagement, heat and the powered equipment budget. Do not continue with a hot or damaged termination.

Shield or noise concern

For shielded products, check end-to-end shield design and grounding practice. Mixing shielded and unshielded parts can defeat the intended system.

Port or label mismatch

Trace one cable at a time, compare labels at both ends and update records immediately after correction.

15

Package contents

In the box

1 × UGREEN 70423 patch panel, 1 × user manual, 1 × compact cable-preparation/termination tool, 4 mounting screw sets and 8 cable ties as listed. Exact gallery shows the accessories but the small yellow tool should not be confused with a full-size modular-plug crimper.

Devices, cables, racks, wall boxes, modules, tools and testers are not included unless explicitly named above.

16

Product-specific FAQ

What exactly is UGREEN 70423?
A passive 24-port Cat6 UTP patch panel for terminating and organising permanent network runs in a standard 19-inch rack position.
What is included in the package?
1 × UGREEN 70423 patch panel, 1 × user manual, 1 × compact cable-preparation/termination tool, 4 mounting screw sets and 8 cable ties as listed. Exact gallery shows the accessories but the small yellow tool should not be confused with a full-size modular-plug crimper.
Which cables, modules or devices are compatible?
A standard 19-inch rack/cabinet with 1U space, compatible Cat6 UTP permanent cable, suitable patch leads and T568A/B installation practice. Rack nuts and mounting method must match the actual rack rails.
Does it guarantee the advertised network speed?
Cat6 performance depends on correct pair placement, minimal untwist, cable construction, patch leads, installation quality and test results. The panel is passive and has no switching bandwidth of its own. Test the complete channel rather than judging one component in isolation.
Can it be used in a PoE network?
The panel is passive. No explicit PoE class/current ceiling is verified for SKU 70423; PoE use requires a complete compliant copper channel, correct IDC terminations and thermal/bundle assessment.
Which tools are required?
Rear IDC termination requires the supplied compact preparation/termination tool or another compatible IDC tool as appropriate. Professional testing and rack tools are still required.
Does it split, switch, route or convert a network connection?
No. not an Ethernet switch, router, PoE injector, unmanaged hub, shielded grounding panel, wall faceplate or substitute for rack cable management and channel certification. Any active switching, routing, conversion or power function requires separate purpose-built equipment.
How should a finished installation be tested?
Start with a wire-map or continuity test that checks all required conductors and shield where applicable. Then connect known-good equipment, confirm negotiated link speed and observe errors under normal traffic.
Is it suitable for outdoor or mains-power installation?
No outdoor or ingress-protection rating is verified. This is a low-voltage networking accessory; it is not a mains device. Follow separation, fire, grounding and building rules.
What should I do if the link is intermittent?
Remove power where applicable, inspect for partial insertion, wrong colour order, excessive untwist, nicked conductors, poor strain relief or an incompatible cable/connector fit. Reterminate only with matched parts, then test again.
How is this exact SKU different from similar UGREEN products?
Exact media confirms 24 front ports, rear T568A/B IDC blocks, 1U rack ears, removable label cover, cable ties and the compact yellow preparation tool. The rack width is stated as standard 19-inch; questionable package-size data and unverified third-party test wording are not presented as product specifications.

Exact-model check before ordering

Match SKU 70423, product type, port or die count, cable category/construction and package contents. Similar UGREEN networking accessories can look nearly identical while using different shielding, conductor fit, rack format or termination method.

SKU 7042324 PORTS • CAT6 UTP • 1U 19-INCH

GST Invoice available, just mail back with details to order confirmation mail.

Buy direct from official UGREEN India

GST Invoice, Warranty, authenticity, faster support
Back to top