UGREEN exact-model guide · SKU 10110
UGREEN 10m High Speed HDMI with Ethernet Cable, 4K UHD (10110)
A user-friendly connection guide covering verified performance, real setups, compatibility boundaries, safe handling and troubleshooting for the exact 10m model.
Product overview
Overview
UGREEN 10110 is a 10m passive High Speed HDMI cable with Ethernet for taking digital picture and sound from an HDMI source to a television, monitor, projector or receiver. Its long reach is useful across a room or from an equipment rack, but the route should be tested before it is hidden or permanently secured.
The important buying check is not merely the cable length: confirm connector format, signal direction, output capability and the receiving display input. The two full-size HDMI Type-A plugs form a passive point-to-point link; the cable does not convert HDMI into another connector format.
The stated ceiling is a maximum rather than a forced output. HDMI and DisplayPort equipment exchange capability information, and the source normally selects a mutually supported mode. This description therefore separates what the cable carries from features that must already exist in the connected equipment.
Product highlights
Key features
4K UHD within connected-equipment limits; no exact refresh ceiling is stated
Maximum exact-SKU display mode on a completely compatible path.
10m
Exact cable length for planning equipment position and service slack.
HDMI Type-A male to HDMI Type-A male
The connector pair must match the source output and receiving display input.
Digital video + audio
One physical display link carries compatible picture and source-to-display sound.
No cable driver
Display configuration remains under the source device and operating system.
Exact-media audited
Only current Shopify-owned images attached to this exact product record are used below.
Port and direction check
Choose the right connection
HDMI Type-A male to HDMI Type-A male
The two full-size HDMI Type-A plugs form a passive point-to-point link; the cable does not convert HDMI into another connector format.
Source side: A standard HDMI output on the source device. Adapters, receivers, switches and wall plates in the route must also support the chosen signal.
Display side: A standard HDMI input on the television, monitor or projector and a common mode across every component in the route.
Resolution, refresh and signal
Verified display modes and performance
Maximum verified mode: 4K UHD within connected-equipment limits; no exact refresh ceiling is stated.
1080p and other lower common HDMI modes remain available within the source and display capabilities.
The exact cleaned product record confirms 4K UHD and 1080p support, HDMI Ethernet Channel, ARC and 3D where both devices provide them. Gallery artwork prints an 18Gbps phrase, but no dependable exact refresh ceiling is published for this 10m run, so this page does not promise 4K60.
A cable rating describes the link it can carry under suitable conditions; it does not guarantee application frame rate, force HDR, upgrade a graphics processor or repair an incompatible handshake. For stable setup, begin with a common 1080p mode and increase resolution or refresh only after the direct connection is working.
Build and physical care
Construction and handling
The exact model uses a passive cable form with moulded connector housings and no separate power brick.
- Full-copper conductor wording on the exact listing
- Gold-plated connector wording in exact artwork
- Shielded black round cable
- Moulded Type-A connector housings
- Passive architecture with no booster or external power
Hold the connector housing—not the cable—when plugging or unplugging. Keep bend radii broad, avoid twisting at the strain relief and give longer runs physical support. Contact plating can help resist surface corrosion, but it cannot compensate for a bent port, contamination or a loose intermediary adapter.
Where the cable fits
Use scenarios
Equipment rack to room display
Route one cable from a media player or receiver to a television positioned several metres away.
Computer to meeting-room projector
Use the 10m reach for a presentation path, then confirm the projector’s accepted resolution and refresh rate.
Console to distant television
Connect an HDMI-output console while keeping the cable protected from foot traffic and sharp furniture edges.
Home theatre with AV receiver
Pass picture and sound through a compatible receiver, remembering that the receiver becomes part of the negotiated HDMI chain.
Mirrored or extended workstation display
A computer can mirror or extend its desktop according to its GPU and operating-system settings.
A reliable first connection
Setup and usability guidance
Use this sequence to establish a basic picture before enabling advanced modes.
- Confirm the cable is UGREEN SKU 10110 and that the HDMI Type-A male to HDMI Type-A male pair matches the two devices.
- Power the source and display normally, then select the intended input on the receiving display.
- Connect the source end and display end without forcing, twisting or loading the port.
- Begin with a common 1080p output if the system does not immediately establish a picture.
- After the direct link is stable, select the intended mode up to 4K UHD within connected-equipment limits; no exact refresh ceiling is stated.
- Choose the desired audio-output device and mirror or extended-desktop arrangement on the source.
- Add a receiver, switch, dock, wall plate or adapter only after the direct connection has been verified.
Compatibility explained
Compatible devices and systems
Compatible source types
- HDMI-equipped desktop and laptop computers
- HDMI media players, set-top boxes and Blu-ray players
- PlayStation, Xbox, Nintendo and other consoles with standard HDMI output
- AV receivers, matrix switchers or presentation sources that expose a compatible HDMI mode
Compatible receiving devices
- HDMI televisions and large-format displays
- HDMI monitors
- HDMI projectors
- Compatible AV receivers, soundbars, switches and matrix equipment within the route
No software driver is required. The source GPU or player, any intermediary device, the display and their settings determine resolution, refresh, colour, HDR, HDCP and audio behaviour.
Supported jobs
What this product does
Use the cable for the following exact roles.
- Carries one digital HDMI video signal and associated digital audio over the stated cable length.
- Supports 4K UHD within connected-equipment limits; no exact refresh ceiling is stated on a fully compatible direct path.
- Provides a passive, externally unpowered link between standard HDMI Type-A ports.
- Can pass supported 3D, ARC, CEC and Ethernet Channel signalling when both endpoints implement the feature.
- Supports mirror or extended-desktop use as selected by a compatible computer.
- Works at a lower common mode when the full chain does not sustain the maximum.
These functions remain within one direct display connection. They are not evidence of charging, ordinary USB data, networking, signal splitting or format conversion beyond the connector path specifically described.
Important exclusions
What this product does not do
Knowing the exclusions prevents the most common wrong-cable purchases.
- It does not amplify, repeat or actively equalise the signal.
- It does not convert USB-C, DisplayPort, DVI or VGA into HDMI.
- It does not split one HDMI source across multiple independent displays.
- It does not upscale low-resolution content or increase a game frame rate.
- It does not guarantee that a receiver, switch, coupler or wall plate will pass the stated maximum.
- It does not include an installation conduit, pull sock, signal tester or separate adapter.
Best-practice checklist
What to do
A careful setup protects the ports and makes faults easier to isolate.
- Plan the route and test the full cable at the intended mode before concealing or securing it.
- Keep bends broad and support the cable so the connector is not used as a hanging point.
- Begin troubleshooting at 1080p, then raise resolution and refresh one step at a time.
- Use direct source-to-display testing to isolate a receiver, switch, wall plate or coupler.
- Label both ends before routing through furniture, ceiling spaces or equipment racks.
- Leave service slack without forming a tight coil or pressing the cable against a sharp edge.
Record the working resolution and refresh rate for shared rooms or fixed desks. If another person later changes a receiver, switch, display input or operating-system setting, this baseline makes troubleshooting much faster.
Avoid these mistakes
What not to do
Incorrect connector force and unsupported signal assumptions cause more failures than cable software.
- Do not pull the long cable by an HDMI plug or strain-relief boot.
- Do not sharply bend, crush, staple or trap the cable under furniture.
- Do not assume a long passive route will behave like an active optical or repeater cable.
- Do not bury it in a wall or conduit unless local rules and an appropriate cable rating permit that installation.
- Do not place it outdoors, in standing water or next to high-heat equipment.
- Do not claim a resolution or refresh rate higher than the exact verified ceiling.
Stop using the cable if a connector is bent, loose, cracked, unusually hot or shows exposed conductors. Continuing to test damaged hardware can harm the port and make an otherwise simple compatibility problem harder to diagnose.
Read before installation
Warnings and limitations
The following limits apply even when both connectors appear to fit.
- Long passive HDMI runs are more sensitive to source output strength, intermediary devices and connector condition than short direct links.
- No in-wall, plenum, LSZH, outdoor or fire-resistance rating is published for this exact cable.
- Any coupler, wall plate, switch or receiver adds another HDMI handshake and signal-loss point.
- Optional HDMI functions such as ARC, CEC, 3D and Ethernet Channel require support at both ends.
- Test the cable before permanent routing because an installed run can be difficult to replace.
- If picture sparkles, blanks or loses sync, reduce the mode and test directly before assuming the display is defective.
Exact-model specification table
Technical specifications
| Product type | Passive High Speed HDMI with Ethernet cable |
|---|---|
| Length | 10m |
| Connectors | 2 × full-size HDMI Type-A male |
| Maximum verified mode | 4K UHD within connected-equipment limits; no exact refresh ceiling is stated |
| Lower modes | 1080p and other mutually supported HDMI modes |
| Video / audio | Digital HDMI video with associated source-to-display audio |
| Optional HDMI functions | 3D, ARC, CEC and Ethernet Channel where both endpoints support them |
| Construction | Full-copper conductor wording on the exact listing; Gold-plated connector wording in exact artwork; Shielded black round cable; Moulded Type-A connector housings; Passive architecture with no booster or external power |
| Driver / external power | None required |
| Conversion / splitting | Not supported |
| Installation rating | No in-wall, plenum or outdoor rating stated |
| Troubleshooting baseline | Test direct at 1080p before raising the output mode |
Specifications describe the cable itself. Resolution, refresh rate, HDR, audio formats, HDCP and multi-display behaviour remain negotiated system properties unless explicitly stated otherwise.
What is in the pack
Package contents
1 × UGREEN 10110 10m HDMI cable
The package is treated as a single-cable product. A source device, display, receiver, switch, wall plate, converter, installation conduit and external power equipment are not listed as included.
Inspect the cable and both connector housings before installation. Retain the model identifier so future replacements can be matched to the same length, connector pair and verified performance boundary.
Collapsible answers
Product-specific FAQ
Open any question for a concise answer about SKU 10110.
Which connectors does UGREEN 10110 use?
It uses HDMI Type-A male to HDMI Type-A male. Check the printed port label and physical connector shape on both devices before purchase; USB-C, Mini DisplayPort, smaller HDMI formats and full-size DisplayPort are not interchangeable unless they are specifically listed.
What is the maximum verified video mode?
The exact researched ceiling is 4K UHD within connected-equipment limits; no exact refresh ceiling is stated. The source, graphics hardware, any receiver or switch, the cable path and the display must all expose a common mode, so the system may correctly negotiate a lower resolution or refresh rate.
Can I use the cable in the opposite direction?
The physical connectors match at both ends, but the logical path still runs from a source output to a receiving display input. The cable does not turn an input into an output or create a signal where the device lacks one.
Does it carry audio as well as video?
Yes, it can carry compatible digital source-to-display audio alongside the video signal. The source must be configured to send audio over the selected display connection, and the receiving display or audio device must support the chosen format.
Can I mirror or extend my computer desktop?
Yes, when the computer GPU and operating system support the requested arrangement. Mirror and extend are host settings; the cable carries the negotiated display stream but does not create extra graphics capability.
Does it need a driver or separate power supply?
No cable-specific driver or separate power supply is listed. Connect the correct source and display ports, choose the receiving input, then use the operating-system display settings if the screen is not detected automatically.
Will it work with a game console?
It can connect a console that has a standard HDMI output to a compatible HDMI display. The console, game, display and any receiver still determine the available resolution, HDR and refresh rate.
Does it support HDR?
HDR is not promised as a standalone exact-SKU feature on this page. If connected equipment offers an HDR mode, verify the reported output and display behaviour rather than assuming support from connector shape alone.
Can it provide an internet connection through the display cable?
Only the optional HDMI Ethernet Channel can pass when both connected HDMI devices explicitly implement and enable that feature. Most ordinary setups still need Wi-Fi or a separate Ethernet connection; the cable is not a USB network adapter.
Can I add an adapter, receiver, switch, dock or wall plate?
Possibly, but every added device becomes part of the signal chain and can change the available mode, direction, HDCP handshake or audio route. Test the cable directly first, then add one intermediary device at a time.
What should I try if there is no picture or the screen flickers?
Confirm the correct source and display ports, select the receiving input, reseat both plugs and begin at 1080p. Test a direct source-to-display connection, power-cycle the equipment and then raise the output mode gradually; persistent faults may indicate an incompatible mode, intermediary device or damaged port.
Can I install this cable outdoors or permanently inside a wall?
No exact outdoor, in-wall, plenum, LSZH or fire-resistance rating is stated here. Use an appropriately certified installation cable when local electrical or building rules require one, and always test the complete route before concealment.
Exact-model verification
Research and source note
The exact current record confirms a 10m passive High Speed HDMI-with-Ethernet cable, full-copper wording, 4K UHD and 1080p, plus ARC, HEC and 3D where supported. Because the body omits a precise refresh ceiling and the artwork’s broader 18Gbps phrase is not length-specific, 4K60 is deliberately not promised.
The current Shopify product record and all 5 product-owned gallery items were checked. Only images attached to this exact SKU are embedded, each once, at large editorial width with a unique caption.
