UGREEN 10371
UGREEN 10371 USB 3.0 A-to-A Data Cable, 2m
A 2m nylon-braided USB-A male-to-male cable for data between one USB host and a compatible peripheral whose device-side connection is specifically designed as USB-A.
Product introduction
Overview
UGREEN 10371 is a USB 3.0 Type-A male-to-male cable for a specific peripheral connection in which the computer or other host has a USB-A port and the device has a USB-A receptacle intentionally designed as its upstream data input. Compatible examples can include certain external enclosures, hubs, cooling pads, cameras or AV peripherals, but the device manual must explicitly permit an A-to-A cable.
The cable is 2m/6.6ft long and rated up to a 5Gbps USB 3.0 interface. Actual transfers depend on the two endpoints, ports, storage, controller and workload. A USB 2.0 endpoint works only at its own lower rate.
A male-to-male cable must not be used to connect two computers, two USB chargers or any two USB host ports. Standard USB host ports can both source power; joining them directly can create an unsafe electrical conflict or damage equipment. The current record contains contradictory charging language, so this correction makes no general 3A or charging claim.
At a glance
Key features
Port-by-port clarity
One host end and one explicitly compatible device end
Host-side USB-A plug
Connect to one computer or other USB host port only.
Device-side USB-A plug
Connect only to a peripheral whose manual identifies its USB-A receptacle as the upstream data input.
2m cable run
Provides approximately 6.6ft reach; route it without sharp bends or tension.
USB 3.0 data path
Carries data up to the mutually supported 5Gbps interface ceiling; it is not a video conversion cable.
Correct topology
A-to-A is safe only when one side is a designed peripheral input
Most USB devices do not use a USB-A receptacle as their upstream connection, which makes this cable specialised. Check the device manual, port label and original cable before purchase. A port that merely accepts the plug is not enough to prove the electrical role.
Never join two host ports. This includes two computers, a computer and the output of a charger, or two powered hubs on host-facing sockets. Use a purpose-built data-transfer bridge for computer-to-computer migration.
- Identify one host and one device before connecting.
- Match the original device cable type.
- Disconnect immediately if the endpoints are not clearly documented.
Data integrity
5Gbps requires two USB 3.x endpoints and a healthy path
The cable can carry the stated USB 3.0-class rate only when both ports and the attached device support it. File-copy speed is lower than signalling rate and can be limited by a hard drive, flash storage, filesystem or small-file workload.
The braided exterior improves handling durability but does not make the connectors immune to side-load or repeated bending. Support the 2m route, keep it away from pinch points and unplug by the connector housing rather than the jacket.
- Use direct ports before adding adapters.
- Eject storage before unplugging.
- Coil loosely for storage and protect both plugs.
Real-world applications
Use scenarios
Choose this exact model when its verified connections and limits match the workflow below.
Compatible drive enclosure
Connect a computer to an enclosure whose upstream device port is explicitly full-size USB-A.
Powered USB hub upstream
Replace the host cable only when the hub manual specifies USB-A-to-A for its upstream connection.
Camera or AV peripheral
Use with equipment that documents a USB-A device input for file or control data.
Desk accessory data link
Connect a compatible cooling pad, monitor hub or other peripheral when its manual requires this exact cable topology.
Practical connection order
Setup and usability guidance
A deliberate connection order makes capability checks and troubleshooting easier.
- Read the peripheral manual and confirm it requires USB-A male-to-male.
- Identify the single host port and the single device-side USB-A input.
- Power down equipment first if the device manufacturer recommends it.
- Insert each connector straight without force.
- Power or wake the peripheral and wait for the operating system to detect it.
- Install only the device-specific driver if required.
- Eject any mounted storage before unplugging.
- Remove by gripping the connector housing and coil the cable loosely.
Host and peripheral fit
Compatible devices and systems
Connector shape alone is not enough: the host port, operating system, cable, display and peripheral must support the required function.
Host
One computer or USB host with a full-size USB-A data port.
Peripheral
One device whose manual explicitly identifies a USB-A receptacle as its upstream data connection.
USB versions
USB 3.x endpoints up to the stated 5Gbps interface; USB 2.0 devices fall back to their own rate.
Operating systems
The cable itself needs no driver; the connected peripheral may require software or a supported filesystem.
Verified function scope
What this product does
- Connects one USB-A host to one explicitly compatible USB-A device input.
- Carries USB 3.0-class data up to the stated 5Gbps interface ceiling.
- Falls back to a lower mutually supported USB rate.
- Provides a fixed 2m braided cable route.
Boundaries that prevent a mismatch
What this product does not do
- It does not safely connect two computers or two host ports.
- It does not act as a computer-to-computer transfer bridge.
- It does not convert USB data into HDMI or other display video.
- It does not carry Ethernet without a compatible USB network device.
- It does not have a verified general-purpose charging or 3A role.
Recommended practice
What to do
- Verify the peripheral port role before connection.
- Use exactly one host and one compatible device.
- Eject storage before unplugging.
- Route the 2m cable away from pinch and trip points.
- Grip connector housings rather than pulling the braid.
Avoid common mistakes
What not to do
- Do not connect two computers.
- Do not connect two powered USB host ports or chargers.
- Do not use the cable merely because both sockets physically fit.
- Do not expect USB data to produce display video.
- Do not unplug during an active transfer.
Read before use
Warnings and limitations
Check before connecting or ordering
- Confirm that the peripheral manual specifically calls for a USB-A male-to-male data cable.
- Never connect two computers or two USB host ports.
- Never connect a USB charger output to a computer host port with this cable.
- No general charging or 3A capability is promised because the current record is internally contradictory.
- This is a USB data cable, not HDMI, DisplayPort or a USB video adapter.
- The fixed length is 2m/6.6ft.
- Both endpoints must support USB 3.x to approach the 5Gbps interface ceiling.
Warning / limitation 1
Connecting two USB host ports can create a power conflict and damage equipment.
Warning / limitation 2
The current listing has conflicting charging language; no general charging use is recommended.
Warning / limitation 3
A physically matching USB-A receptacle may still be an output/host port rather than a device input.
Warning / limitation 4
Unexpected removal can corrupt files on connected storage.
Warning / limitation 5
Stop use if a connector, strain relief or braid is cut, loose, bent or unusually hot.
Model-specific data
Technical specifications
| Specification | Verified detail |
|---|---|
| Brand / SKU | UGREEN 10371 |
| Product type | USB 3.0 data cable |
| Connectors | USB-A male to USB-A male |
| Length | 2m / approximately 6.6ft |
| Maximum interface rate | Up to 5Gbps |
| Cable exterior | Nylon braided |
| Required topology | One USB host to one explicitly compatible peripheral input |
| Computer-to-computer | Not supported; use a purpose-built transfer bridge |
| Video conversion | Not supported |
| General charging claim | Not made due conflicting current record |
| Driver | No cable driver; peripheral may require one |
Verified in-box information
Package contents
- 1 × UGREEN 10371 USB-A male-to-male data cable, 2m.
No host adapter, peripheral, storage enclosure, charger or transfer-bridge electronics are included.
Model-specific answers
Product-specific FAQ
Can I connect two computers with UGREEN 10371?
No. Never connect two USB host ports directly. Use a purpose-built computer-to-computer transfer bridge.
Why are both connectors USB-A male?
The cable is for specialised peripherals whose upstream device input is a USB-A receptacle. Check the device manual.
Can I connect a charger to my laptop with it?
No. Do not join a charger output and computer host port with this A-to-A cable.
Does it support charging?
The current record is contradictory, so no general charging or 3A use is recommended. Treat it as a compatible peripheral data cable only.
What is the maximum data rate?
The stated USB 3.0 interface ceiling is up to 5Gbps when both endpoints support it.
Will a USB 2.0 device work?
A compatible device can fall back to its lower USB 2.0 rate.
Can it output video to a monitor?
No. It is not an HDMI, DisplayPort or USB graphics adapter.
Is it suitable for every hard drive enclosure?
No. Use it only when the enclosure has a USB-A device-side input and its manual specifies an A-to-A cable.
Does the cable need a driver?
No. The connected peripheral may require its own operating-system driver.
How should I disconnect a drive?
Eject the mounted volume, wait for activity to stop and pull by the connector housing.
How long is the cable?
It is 2m, approximately 6.6ft.
